You are in: Home > CATALOGUE > Accessories for Cables and Connectors

Do you need a quote? CONTACT US! (click here)

Accessories for Cables and Connectors

POTA-SPEED guarantees fast and practical management of the coaxial cables coils (recommended for cables up to max. 10mm/.400" diameter) You can find below a video where the advantages during use are highlighted. Preface and Backstage of the projects We would first like to thank Mike K8MRD and our friend Stephen for contributing their very detailed advice in creating products strongly inspired by POTA enthusiasts. The objective was to build a high visibility cable suitable for intensive use, subject to continuous handling and trampling, for situations in the field, without compromises, breaking the traditional mold. These cables had to inherit the extreme flexibility of our Ultraflex and Hyperflex class models (specific for combination with rotors) and they also had to inherit the lightness of the Extraflex Bury series, robust as tanks and buryable but less flexible. Often creating a product that brings together the best of each ...

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 16.90

Select

Crimping Tool for 50 Ohm Connectors

The product includes x1 Crimping Tool and x2 interchangeable dies, to be used according to the type of cable and connector. #1 Die CompatibilityHole .256 = SMA and BNC Connectors for Hyperflex 5Hole .068 = SMA and BNC Pin for Hyperflex 5Hole .295 = N and SMA type Connector for Ultraflex 7 #2 Die Compatibility Hole .100 = N type and SMA Pin for Ultraflex 7 and all 10,3mm (.400") CablesHole .128 = N type Pin for all 10,3mm (.400") CablesHole .429 = N type Connector for all 10,3mm (.400") Cables

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 45.7866

Select

M&P Flux for Soldering/Desoldering

Why should the use of M&P-Flux always be considered? The M&P-Flux is now the faithful companion of all the specialized technicians involved in soldering on printed microcircuits. It can be used in a very convenient way both in the soldering phase and in the desoldering phase, due to the following reasons. 1) Improvement of thermal conductivity and capillarity: Its chemical composition facilitates the entry of molten tin, causing it to be sucked by "capillarity" inside the hole in the UHF EVO pins, or the N pins or PL259 connectors and any other solder connector. 2) This occurs by leaving the outer surface of the pin, clean and therefore free of unwanted accumulations of solder. 3) The capillarity phenomenon described above generates greater welding speed, which results in less thermal stress for the dielectric of the coaxial cable which could deform due to too much prolonged heat. 4) The resulting welding is never cold and opaque, but ...

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 3.00

Select

Special Coax Scissors

WHY CHOOSE THIS PRODUCT:Italian production scissors designed by Messi & Paoloni to ensure precision and delicacy while cutting the cable, consisting of an insulated handle in cellulose acetate, and a special nickel-plated cable stripper blade with a semi-lunar shaped recess for an accurate cut of any layer of the cable. The cut is clean and without metal burrs, even on the central conductors of considerable sizes, such as our 12,7mm (.500") cables, greatly facilitating the insertion of the inner conductor in the pins (for example of the N or UHF EVO connectors). Made with a special carbon steel (XC50 with Rockwell HRC 53-56 hardness) and bainitic hardening treatment, they guarantee prolonged use by reducing wear in the recess of the blade.To preserve the quality of the cut given by the semi-lunar recess of the blade for a long time, we recommend cutting only cables with copper conductors only or CCA (copper-plated aluminum), avoiding those in CCS (copper-plated ...

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 19.90

Select

Silicone Seal L

WATCH THE VIDEO BELOW TO DISCOVER ALL THE ADVANTAGESSelf-tightening silicone rubber tubular gasket for our cables Ø7,3mm (.287”) or Ø10,3mm (.400”) or Ø12,7mm (.500”), matched to any one of our related connectors and adapters (Except 7/16 and right-angle connectors if installed before inserting it).M&P-Silicone-Seal-L: reliable optimal tubular gasket that quickly seals the male-female connection, or connector-adapter-connector, tightly, hermetically, and seamlessly. No flame or heat is required. It is also handy as a strain relief, for increasing the tensile strength between cable and connector!The M&P-silicone-seal is factory expanded and assembled onto a removable supporting plastic core. The pre-stretched M&P-silicone-seal-L, as the core is unwound, (from the inside), shrinks to form a thick and tight tubular gasket. Retains its resiliency and pressure even after years of aging and exposure to Ultra-violet rays, acids, ...

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 6.003

Select

"50 Ohm Cables" and "Antenna TV Cables" - DISCOUNTED from 10% to 20%!

Silicone Seal S

WATCH THE VIDEO BELOW TO DISCOVER ALL THE ADVANTAGESSelf-tightening silicone rubber tubular gasket for our cables Ø 7,3mm (.287”) or 10,3mm (.400”) or 12,7mm (.500”), matched to any one of our related connectors and adapters (Except 7/16 and right-angle connectors if installed before inserting it). M&P-Silicone-Seal-S is a reliable tubular gasket that quickly seals the socket of the 50-ohm Antennas with the down lead cables, tightly, hermetically, and seamlessly. No flame or heat is required. One more application: you may use it inside an electrical cabinet to protect your connections from condensation. (Extension leads etc.) It is also handy as a strain relief, for increasing the tensile strength between cable and connector! The M&P-Silicone-Seal is factory expanded and assembled onto a removable supporting plastic core. The pre-stretched M&P-Silicone-Seal-S, as the core is unwound (from the inside), shrinks to form a thick and tight tubular gasket. Retains its resiliency and ...

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 4.968

Select

Cable Pulling Lubricant for Conduit Passage

Are you about passing your cables in narrow pipes? Are you sweating at the thought of doint it? With this special cable transparent lubricant, you will easily pass your professional M&P cables through! It is a gelatinous lubricant for installation of coaxial cables, optical fiber and electrical cables, also in vertical position. It does not produce the glue effect, it is also indicated for machines slips cables. Non-toxic, inert, biodegradable and non-flammable. *Bottle of 1 L

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 9.2354

Select

Compact Size Tool for ''F'' Compression Connectors (VT300)

Connectors tool compatible for: Compression type "F" PPC connectors CMPMC 37 EX6-4,9/8,3 EX6-5,1/8,3 EX 11 Compression type "F" PPC AquaTight connectors CMPMC 37-A EX6-4,9/8,3-A EX6-5,1/8,3-A BOO4-FM

Details

Availability:

Total Price
(VAT excluded) € 59.90

Select

Arianna Cable Unwinder

Suitable with all cables up to 6,9mm of diameter (max 100m) All weak points have been strengthened in order to resist to heavy duty. The shape also lets you use ita as...an emergency seat or stool. Sturdy and long lasting, made by moplen, abs, stainless steel, brass and made by means of 4 dies only. It weights 1,6 Kg only. Two special slots at the back let you hold scissors and screwdriver (not included in the kit). It has rubber slip-proof feet. The shoulder strap has a soft rubber pad to cushion the contact point and prevent slipping. You can place 4 or 5 Arianna underwinders side-by-side, then connecting the ends to a probe you can simultaneously insert several cables into the duct.Weight: 1,6 Kg | Size: 35cm x 32cm x 14cm

Details

Quantity

Availability:

delivered in 2-4 days

Total Price
(VAT excluded) € 48.80

Select