Why should the use of M&P-Flux
always be considered?
The M&P-Flux is now the faithful
companion of all the specialized technicians involved in soldering on printed
microcircuits.
It can be used in a very convenient
way both in the soldering phase and in the desoldering phase, due to the
following reasons.
1) Improvement of thermal
conductivity and capillarity:
Its chemical composition facilitates
the entry of molten tin, causing it to be sucked by "capillarity"
inside the hole in the UHF EVO pins, or the N pins or PL259 connectors and any
other solder connector.
2) This occurs by leaving the outer
surface of the pin, clean and therefore free of unwanted accumulations of solder.
3) The capillarity phenomenon
described above generates greater welding speed, which results in less
thermal stress for the dielectric of the coaxial cable which could deform due
to too much prolonged heat.
4) The resulting welding is never
cold and opaque, but shiny and ...
...........................................................................
WHY CHOOSE THIS PRODUCT:Italian production scissors designed by Messi & Paoloni to ensure precision and delicacy while cutting the cable, consisting of an insulated handle in cellulose acetate, and a special nickel-plated cable stripper blade with a semi-lunar shaped recess for an accurate cut of any layer of the cable.
The cut is clean and without metal burrs, even on the central conductors of considerable sizes, such as our 12,7mm (.500") cables, greatly facilitating the insertion of the inner conductor in the pins (for example of the N or UHF EVO connectors). Made with a special carbon steel (XC50 with Rockwell HRC 53-56 hardness) and bainitic hardening treatment, they guarantee prolonged use by reducing wear in the recess of the blade.To preserve the quality of the cut given by the semi-lunar recess of the blade for a long time, we recommend cutting only cables with copper conductors ...
Self-tightening silicone rubber tubular gasket for our cables Ø 5,4 (.212”) or 7,3mm (.287”) or 10,3mm (.400”) or 12,7mm (.500”), matched to any one of our related connectors and adapters (Except 7/16 and right-angle connectors if installed before inserting it).M&P-Silicone-Seal-L: reliable optimal tubular gasket that quickly seals the male-female connection, or connector-adapter-connector, tightly, hermetically, and seamlessly. No flame or heat is required.
It is also handy as a strain relief, for increasing the tensile strength between cable and connector!The M&P-silicone-seal is factory expanded and assembled onto a removable supporting plastic core. The pre-stretched M&P-silicone-seal-L, as the core is unwound, (from the inside), shrinks to form a thick and tight tubular gasket. Retains its resiliency and pressure even after years of aging and exposure to Ultra-violet rays, acids, condensation and harsh environments, with operating temperature ...
Self-tightening silicone rubber tubular gasket for our cables Ø 7,3mm (.287”) or 10,3mm (.400”) or 12,7mm (.500”), matched to any one of our related connectors and adapters (Except 7/16 and right-angle connectors if installed before inserting it). M&P-Silicone-Seal-S is a reliable tubular gasket that quickly seals the socket of the 50-ohm Antennas with the down lead cables, tightly, hermetically, and seamlessly. No flame or heat is required.
One more application: you may use it inside an electrical cabinet to protect your connections from condensation. (Extension leads etc.) It is also handy as a strain relief, for increasing the tensile strength between cable and connector! The M&P-Silicone-Seal is factory expanded and assembled onto a removable supporting plastic core. The pre-stretched M&P-Silicone-Seal-S, as the core is unwound (from the inside), shrinks to form a thick and tight tubular gasket. Retains its resiliency and pressure even ...
...........................................................................
Are you about passing your cables in narrow pipes? Are you sweating at the thought of doint it?
With this special cable transparent lubricant, you will easily pass your professional M&P cables through!
It is a gelatinous lubricant for installation of coaxial cables, optical fiber and electrical cables, also in vertical position.
It does not produce the glue effect, it is also indicated for machines slips cables.
Non-toxic, inert, biodegradable and non-flammable.
*Bottle of 1 L
...........................................................................
Suitable with all cables up to 6,9mm of diameter (max 100m)
All weak points have been strengthened in order to resist to heavy duty. The shape also lets you use ita as...an emergency seat or stool. Sturdy and long lasting, made by moplen, abs, stainless steel, brass and made by means of 4 dies only. It weights 1,6 Kg only. Two special slots at the back let you hold scissors and screwdriver (not included in the kit). It has rubber slip-proof feet. The shoulder strap has a soft rubber pad to cushion the contact point and prevent slipping. You can place 4 or 5 Arianna underwinders side-by-side, then connecting the ends to a probe you can simultaneously insert several cables into the duct.Weight: 1,6 Kg | Size: 35cm x 32cm x 14cm
...........................................................................
If you want to purchase this product, write us at web@messi.it
This special stand can be moved very easily: one person can load it without effort into a van, even with all the cables in place. It's well balanced, in order that anyone can handle it the same way as a baby stroller.
Suitable for showroom or workshop, it holds a poster on top which show the cables' features for a quick and easy reading. Great Marketing device!
Following is a sharp and clear view of how could be possible to "dress up" your Cable trolley.
We have added a bracket holding a set of cables 1 m long (3 feet) , hanging for customers flexibility test.
Moreover, it's also available a winding device with meter-counter, for the making of customized coils.
*METERCOUNTER and BOBBIN WINDER ARM are sold separately.